Data Ops - O&M: Modem

Showing posts with label Modem. Show all posts

Quick Guide to AZTECH CPE - DSL5028EN(1T1R)

Aztech CPE
Model : DSL5028EN(1T1R)
ADSL2+ 4-Port 150Mbps Wireless-N
Modem Router

Quick Setup Guide

Aztech ADSL2+ 150Mbps WIRELESS-N
4-Ports Modem Router
Model : Wireless N DSL5018EN(1T1R)

Default IP Address: 192.168.1.1
Note: you have to synchronized the modem with DSLAM before accessing via web browser

Router Mode Configuration
+ Click Network Button
+ Click Internet menu
- Select Activated as Status
- Select VPI/VCI
- Select Static as Connection Type
- Select 1483 Bridged IP LLC as encapsulation
- Select Yes as Default Route
- Enter Point-To-Point or WAN IP
* IP Address
* Subnet Mask
* Gateway
* DNS
- Select enable NAT
- then click Apply button

+ Click Local menu
- enter LAN IP in Router IP Address box
- enter the LAN Subnet mask
- Select Enable/Disable DHCP Server
- Then click Apply button

+ Click System Button
- click reboot button under reboot menu

For Wireless Configuration

+ Click Wireless button
- Select enable wireless
- Enter desire SSID Name
- Select enable Broadcast SSID
- Select 802.11b+g+n wireless mode
- Left all setting as-is
- then click Apply button

+ Click Secuity menu
- Select WPA-PSK/WPA2-PSK as security mode
- Select TKIP/AES combination as Encryption
- Enter preshared key for Wifi Password
- then click Apply button

for Advance setup configuration, leave your comment here

*That's it

Quick Guide for KASDA (KD212) DSL Modem

Kasda KD212

A sample router mode configuration for this type of DSL Modem.

+ Click Advance Setup menu
+ Click Layer2 Interface
- Click ATM Interface
- Use VPI/VCI define by ISP
- Select Path0 as DSL Latency
- Select EoA as DSL Link
- Select Default Mode as Connection Mode
- Select LLC/SNAP-BRIDGING as encapsulation mode
- Select UBR without PCR as Service Category
- Select Strict Priority as IP QoS Scheduler Algorithm
- Then click Apply/Save button
+ Select WAN Service
- Click Add Button
- Select a Layer2 Interface that previously configured then click
Next button
- Select IP over Ethernet then click Next button
- Select Static IP Address then input the WAN IP address or Point-to-Point
IP Address given by ISP then click Next button
- Select Enable NAT, Enable Firewall (optional) then click Next button
- Click Next for Routing – Default gateway
- Enter ISP DNS Server then click Next button
- Click Apply/Save button
+ Select LAN
- Write down first usable IP Address given by ISP and the corresponding
subnet mask.
- Disable/Enable DHCP server depending on client configuration then click
Apply/Save button
+ Click Management menu
- Click Reboot menu and reboot button.
- Test the modem after rebooting and insync with the DSLAM.

How to Access Actelis ML62x - Using Management Interface in MetaAssist View

I have been using this modem for a while now, and i want to share a useful tip on how to access your modem using management interface. Let's say, you forgot your usb-to-serial interface cable or a serial cable (db9 connector) and cannot access the modem locally using your laptop to check an alarm.

Ok here's the simple tip.

+ Before you deploy your modem to remote sites, make sure that
COLAN interface port is set to Enable.

+ Open the Management Interface Menu, and set an Ip Address to
IP Interface.

e.g.

* IP Address: 10.10.10.10

* Subnet Mask: 255.255.255.0

* Gateway: 10.10.10.1

+ Close and Open the MetaAssist View, then use a cross-over cable
and plug it into MGMT port of the modem.

NexComm N560 (EoC) Simple Setup Configuration

Here is a simple way on how to configure a two N560 model.

Know the 2Base-TL Pin Assignment (RJ45 connector)

o Line #1 – Blue/White-Blue

o Line #2 – Brown/White-Brown

o Line #3 – Green/White-Green

o Line #4 – Orange/White-Orange

· Configure the Laptop or Desktop to access modem

o IP Address: 172.16.0.56

o Subnet Mask: 255.255.255.0

o Gateway: 172.16.0.55

· Access N650 via Telnet or Serial Port

o For telnet;

§ Run command “telnet 172.16.0.55”

o For Serial Port ,

§ Data rate : 38400

§ Data bits : 8

§ Stop bits : 1

§ Parity : None

§ Flow Control : None

· Default User access

o Username : admin

o Password : password

o Enable password : password

· Modem #1 Config

o N560>(enable) set system time {time}

o N560>(enable) set system hostname {hostname}

o hostname >(enable) set devicetype co

o hostname >(enable) set devicemode binding

o hostname >(enable) set vlmode transparent

o hostname >(enable) restart pme all

o hostname >(enable) write config0

· Modem #2 Config